Skip to content

SMTP Error 5.7.1: What It Means and How to Fix It Fast

SMTP error 5.7.1 is a permanent refusal based on policy. This guide lists the common causes (relay, reputation, rate limits, malformed headers) and the fix for each.

Nov 15, 2026 4 min read 987 words
SMTP Error 5.7.1: What It Means and How to Fix It Fast

Getting a bounce that says 550 5.7.1 is frustrating, because the message looks final. This SMTP error is fixable once you know which rule you hit. Below you will find what it means, the usual causes, and a step-by-step fix.

TL;DR

  • SMTP error 5.7.1 is a permanent failure. The receiving server refused your message because of a policy, not because the address does not exist.
  • Common causes are relay without authentication, a poor IP or domain reputation, rate limiting, and malformed headers.
  • Read the text after the code. It usually names the exact reason.
  • Fix the cause, then resend. Retrying the same message unchanged will fail again.
SMTP error 5.7.1 bounce message explained
SMTP error 5.7.1 bounce message explained

What does SMTP error 5.7.1 mean?#

Every SMTP failure carries an enhanced status code. The first digit tells you how serious it is. A 5 is a permanent failure, so the receiving server will not accept the message as sent. The second digit, 7, groups errors about security and policy. The last digit, 1, is the general "delivery not authorized, message refused" case defined in RFC 3463.

So SMTP error 5.7.1 reads like this: the server understood your message, but a rule says it will not deliver it. It often appears as 550 5.7.1, followed by a short explanation.

Do not confuse it with a bad address. A missing mailbox is usually 5.1.1. If you want to see how other codes compare, read our guide to email bounce codes.

Common causes of SMTP error 5.7.1#

Google's SMTP error reference lists several 550 5.7.1 variants. Other providers use the same code with different wording. These are the main groups.

Cause Typical message Where it is fixed
Relay not allowed Invalid relay credentials, or the IP is not authorized Your mail server or relay settings
Low reputation Low IP or domain reputation Your sending practices
Likely unsolicited Message looks like unwanted mail Your list and content
Rate limited Email has been rate limited Your sending speed
Policy block The domain prohibits the email The recipient's admin
Malformed message Missing or duplicate headers Your mail software

Relay or authentication problems#

Many 5.7.1 errors happen when you send through a server that does not trust you. Examples are an unregistered IP, a missing login, or a relay that only accepts certain senders.

Fix: authenticate with SMTP AUTH, send through your provider's relay, and make sure your sending IP or domain is registered where required.

Poor sender reputation#

If receivers see spam-like traffic from your IP or domain, they refuse mail by policy. You may see wording about low IP or domain reputation.

Fix: lower your complaint and bounce rates, stop mailing unengaged contacts and warm up new domains slowly. Our guide on sender reputation explains what receivers look at.

Rate limiting#

Sending too much too fast triggers a refusal. Gmail, for example, may answer 550 5.7.1 with a rate-limit message.

Fix: slow down, spread sends over the day and respect your provider's limits.

Malformed headers#

Messages with a missing From, a missing Message-ID, or duplicate headers can be rejected. This is common with custom scripts and some marketing tools.

Fix: make sure each required header appears exactly once and uses plain ASCII where required.

A policy set by the recipient#

Some domains block senders by rule, for example a company that only accepts mail from certain domains.

Fix: you cannot change their policy. Ask the recipient to contact their administrator and allow your sender.

How to fix SMTP error 5.7.1 step by step#

  1. Read the full bounce. Copy the text after the code. It is more useful than the number.
  2. Check authentication. Confirm SPF, DKIM and DMARC pass for your sending domain. Our guide to setting up SPF, DKIM and DMARC walks through it, and an SPF checker shows if your record is valid.
  3. Look for blocklists. Test your IP and domain with a blacklist checker.
  4. Review your list. Bad addresses create bounces, and bounces hurt reputation. Verify addresses first with an email verifier.
  5. Slow your sending. Cut volume per hour and per domain, then ramp up gradually.
  6. Resend a corrected message. Only retry once you have changed something.

How to prevent SMTP error 5.7.1#

  • Keep bounce rates low by cleaning your list before every campaign.
  • Authenticate every sending domain.
  • Warm up new mailboxes and domains instead of sending at full volume on day one.
  • Use a dedicated sending domain for outreach so problems stay contained.
  • Watch your domain reputation in Google Postmaster Tools.

Quick checklist before you resend#

Run through this short list. Is your SPF, DKIM and DMARC authentication passing? Is your IP or domain on a blocklist? Did you send a large batch in a short time? Does the message have one valid From header? Did you verify the recipient address? Most SMTP errors of this type disappear after one of these is corrected.

FAQ#

Is SMTP error 5.7.1 permanent?#

Yes. The leading 5 marks a permanent failure for that message. A different version of the message, sent after you fix the cause, can still succeed.

Is a 5.7.1 error the same as a spam block?#

Sometimes. Spam and reputation are common causes, but relay, rate limits and recipient policies also use 5.7.1.

Does 5.7.1 mean the email address is invalid?#

No. An invalid address normally returns 5.1.1. The 5.7.1 code is about policy.

Should I retry after a 5.7.1 bounce?#

Not unchanged. Find the reason in the bounce text, fix it, and send again.

How do I stop getting 5.7.1 errors on cold email?#

Authenticate your domain, keep volume modest, and verify every address before sending. Most outreach bounces trace back to unverified data.

Keep bounces low#

A clean list is the simplest defence against policy blocks. Try Tomba's email verifier to check addresses before you send.

// start free

See who Tomba finds at any company

Type a company's domain to see its people, their roles and verified work emails, each with the pages it was found on. Free account, no card.

Free plan · No credit card required · GDPR & CCPA

Share
0 clapsEnjoyed it? Give a clap.
AU

// about the author

Tomba Editorial Team

Was this helpful?